The Epson TM-m30 and TM-m10 are compact Bluetooth thermal printers that work great with Dinevate. This guide walks you through the whole setup, from loading paper to printing your first order ticket. The steps are the same for both models (the TM-m30 uses 80mm paper, the TM-m10 uses 58mm paper).
Before you start: Printers connect to your tablet (running the Dinevate Order Manager app), not to the website. Keep the printer and tablet within a few feet of each other while you set up.
What You'll Need#
- Your Epson TM-m30 or TM-m10 printer and its power adapter
- A roll of thermal receipt paper (80mm for the TM-m30, 58mm for the TM-m10)
- Your Dinevate tablet, powered on and running the Dinevate Order Manager app
- Bluetooth turned on on the tablet
Step 1: Load the Receipt Paper#
- Lift the gray cover-release latch on top of the printer to pop the cover open.
- Drop the paper roll in so the paper feeds from the bottom of the roll (this matters: if it feeds from the top, nothing will print).
- Leave a little paper sticking out, then close the cover firmly until it clicks.
- Tear off the extra paper against the cutter.
Tip: Epson printers use heat-sensitive thermal paper; there is no ink or toner. If a printed receipt is blank, the roll may be in upside down. Flip it so it feeds from the bottom.
Step 2: Power On and Wait for "Ready"#
- Plug in the power adapter and press the power button.
- Watch the lights on the front. Wait until the status light is solid blue and the other lights have turned off.
A solid blue status light means the printer has finished starting up and is discoverable over Bluetooth.
Tip: If a light keeps blinking or an error light stays on, the cover may not be fully closed or the paper may be out. Re-seat the paper, close the cover, and power off and on again.
Step 3: Pair the Printer in the Tablet's Bluetooth Settings#
First pair the printer at the tablet level, exactly like you would any Bluetooth device.
- On the tablet home screen, tap the three dots ( ⋮ ) in the top-right corner.
- Tap Bluetooth.
- Make sure Bluetooth is turned on (the toggle should be blue/green).
- In the list of available devices, find your printer. It appears as TM-m30_XXXXXX (or TM-m10_XXXXXX), where the X's are part of the printer's serial number.
- Tap it to pair. On Android, tap OK (or Pair) to confirm.
- If you are asked for a pairing code, enter 0000, or try 1234. (Most Epson printers pair without asking for a code at all.)
When it is done you should see the printer listed as Paired or Connected.
Note: This pairing happens once at the tablet level. After this, the tablet remembers the printer.
Step 4: Add the Printer in the Dinevate Order Manager App#
Now register the printer inside the app so it can print order tickets.
- From Order Manager Home, open Settings → Printers & receipts → Printers & station routing.
- In Find your printer, choose Bluetooth, then Epson under Printer brand. If you are already editing a saved printer, tap Add printer first.
- Tap Search for printers. Allow Bluetooth or Nearby devices access if the tablet asks.
- Select your printer from the results. Set up one printer at a time.
- On Check the actual test receipt, tap Print test once and check the paper from the selected printer.
- Tap Yes, printed correctly only when a readable receipt comes from the correct printer. If it does not, choose No, something is wrong, check the printer, and retry the test.
If the Scan Doesn't Find Your Printer#
Use the manual option instead:
- In Find your printer, keep Bluetooth and Epson selected, then tap Enter Bluetooth address manually.
- Enter the Epson model from the printer's label and its Bluetooth address. Use the printer's address, not the tablet's.
- Tap Continue to test, then complete the Print test and receipt confirmation above.
You can find the MAC address two ways:
- It is printed on the label on the bottom or back of the printer (it looks like
AA:BB:CC:DD:EE:FF). - Or print a status sheet: turn the printer off, then hold the Feed button while turning it back on, and release once it starts printing. The sheet lists the Bluetooth address.
Important: For the manual option to work, the printer must already be paired in the tablet's Bluetooth settings (Step 3).
Step 5: Choose What This Printer Prints#
After you confirm the test receipt, the app opens What should this printer print?
- Enter a recognizable Printer name, such as Front counter.
- Open Print tasks and select Customer receipt, your station tickets, or both. Station names come from your restaurant's setup, such as Kitchen tickets or Pizza tickets. Select at least one task.
- Set Copies per task from 1 to 10. Most restaurants use 1.
- Tap Save printer and wait for Printer saved, then tap Done.
These printer assignments are saved for this tablet. To add another printer, use Add another printer and repeat the test and task selection.
Example: With one Epson TM-m30 at the front counter, select Customer receipt and the kitchen station's tickets so both print there.
Step 6: Turn On Automatic Printing#
To print configured tickets when an order is accepted:
- Return to Settings → Printers & receipts.
- Under Automatic printing, turn on Automatically print accepted orders.
- If you also want incoming orders accepted automatically, open Settings → Order behavior → Incoming orders and turn on Automatically accept orders.
An ASAP order of $100 or more still needs a manual check before acceptance. Automatic acceptance also requires the signed-in employee's permission to accept orders. See Automatically accept orders for the full behavior.
If automatic printing is off, open an order and tap Print to choose its receipts and station tickets.
Troubleshooting#
The printer doesn't show up#
- Confirm the status light is solid blue (Step 2). If it is blinking, reload the paper, close the cover, and power off and on.
- Make sure Bluetooth is on on the tablet ( ⋮ → Bluetooth) and the printer is within a few feet.
- If you already paired it in the tablet's Bluetooth settings but the in-app scan misses it, choose Bluetooth → Epson → Enter Bluetooth address manually and enter the printer's model and address.
It asks for a pairing code#
- Enter 0000 first, then try 1234. Most Epson units pair without any code.
The test print doesn't come out#
- Check that paper is loaded feeding from the bottom and the cover is fully closed.
- Look for a paper-out or error light and clear it.
- Open Settings → Printers & receipts → Printers & station routing, select the saved printer, tap Test printer, then Print test. Confirm whether a readable receipt printed.
Orders don't print automatically#
- In Settings → Printers & receipts → Automatic printing, make sure Automatically print accepted orders is on.
- Open Printers & station routing, select the printer, and check its Print tasks and Copies per task.
- Check that the order has been accepted. ASAP orders of $100 or more need a manual check even when automatic acceptance is on.
- Open the order and tap Print to check the saved printer. If that fails too, use Test printer and check the paper and connection.
Still Need Help?#
From the tablet, open Support on Home and choose Create New Case when permitted. Mention that you are setting up an Epson TM-m30 / TM-m10 printer and describe what you see (for example, "printer pairs but the test print fails"). Our team will help you get it printing.